Ethernet Remote I/O ioLogik E2242

0 in Stock

Smart I/O controller with 4AI and 12DIO, Click&Go Front-end intelligence

Brand: Moxa

Moxa’s ioLogik E2200 Series Ethernet Remote I/O is a PC-based data acquisition and control device that uses proactive, event-based reporting to control I/O devices and features the Click&Go programming interface. Unlike traditional PLCs, which are passive and must poll for data, Moxa’s ioLogik E2200 Series will, when paired with our MX-AOPC UA Server, communicate with SCADA systems using active messaging that is pushed to the server only when state changes or configured events occur. Additionally, the ioLogik E2200 features SNMP for communications and control using an NMS (Network Management System), allowing IT professionals to configure the device to push I/O status reports according to configured specifications. This report-by-exception approach, which is new to PC-based monitoring, requires far less bandwidth than traditional polling methods.


ioLogik E2242 Specifications

Inputs and Outputs
Configurable DIOs (by software): 12 channels
Analog Inputs: 4 channels
Isolation: 3k VDC or 2k Vrms

Digital Input
Sensor Type: Wet Contact (NPN or PNP) and Dry Contact
I/O Mode: DI or Event Counter
Dry Contact:
• On: short to GND
• Off: Open
Wet Contact (DI to GND):
• On: 0 to 3 VDC
• Off: 10 to 30 VDC
Common Type: 6 points per COM
Isolation: 3k VDC or 2k Vrms
Counter Frequency: 900 Hz
Digital Filtering Time Interval: Software selectable

Digital Output
Type: Sink
I/O Mode: DO or Pulse Output
Pulse Output Frequency: 1 kHz
Over-Voltage Protection: 45 VDC
Over-Current Protection: 2.6 A (4 channels @ 650 mA)
Over-Temperature Shutdown: 175°C (min.)
DIO Output Leakage Current: 4.0 mA @ 24 VDC
Current Rating: 200 mA per channel

Analog Input
Type: Differential input
Resolution: 16 bits
I/O Mode: Voltage / Current (software selectable)
Input Range: ±150 mV, 0 to 150 mV, ±500 mV, 0 to 500 mV, ±5 V, 0 to 5 V, ±10 V, 0 to 10 V, 0 to 20 
mA, 4 to 20 mA
±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
±0.5% FSR @ -40 and 75°C
Sampling Rate:
All channels: 32 samples/sec
Per channel: 8 samples/sec 
Single channel: 100 samples/sec
Input Impedance: 200 kilo-ohms ohms (min.)
Built-in Resistor for Current Input: 120 ohms

Power Requirements
Input Voltage: 12 to 36 VDC
Input Current: 178 mA @ 24 VDC

We are unable to allocate a specific time for delivery. You may let us know your preferred timing and we will try our best to meet your request if possible.
Yes, for urgent purchases, please contact TNS before placing your order
Yes, TNS offers international shipping out of Singapore. Our delivery partners are Fedex and DHL. Product prices quoted on our website is in Singapore currency by default.
Enjoy free local delivery service for online order over S$80. Free delivery service is within Singapore mainland (excluding Jurong Island, shipyards and restricted locations).
To ensure the safe delivery of your order, it is recommended to indicate your full name that matches your valid identification document (ID).
Unless specified, there is no minimum order.
TNS accepts payment via credit card, paynow transfer, cash and funds wired to our bank.
No registration is necessary. Your product is registered at the time of purchase.
TNS offers advice on product configuration and technical support. Our support hotline +65-67476740 is open from 9am to 5.30pm on weekdays. You can also email your questions to us.
Write Your Own Review
Start your review of Ethernet Remote I/O ioLogik E2242: