Ethernet Remote I/O ioLogik E2240

Smart I/O controller with 8AI and 2AO, Click&Go; Front-end intelligence

$272.50
9% Tax included Shipping calculated at checkout.
Available Models

Moxa’s ioLogik E2200 Series Ethernet Remote I/O is a PC-based data acquisition and control device that uses proactive, event-based reporting to control I/O devices and features the Click&Go programming interface.

Unlike traditional PLCs, which are passive and must poll for data, Moxa’s ioLogik E2200 Series will, when paired with our MX-AOPC UA Server, communicate with SCADA systems using active messaging that is pushed to the server only when state changes or configured events occur. Additionally, the ioLogik E2200 features SNMP for communications and control using an NMS (Network Management System), allowing IT professionals to configure the device to push I/O status reports according to configured specifications. This report-by-exception approach, which is new to PC-based monitoring, requires far less bandwidth than traditional polling methods.

Moxa ioLogik E2240 Specifications

Inputs and Outputs
Analog Inputs: 8 channels
Analog Outputs: 2 channels

Analog Input
Type: Differential input
Resolution: 16 bits
I/O Mode: Voltage / Current
Input Range: ±150 mV, ±500 mV, ±5 V, ±10 V, 0 to 20 mA, 4 to 20 mA
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
±0.5% FSR @ -40 and 75°C
Sampling Rate:
All channels:
• 10 samples/sec for voltage
• 6 samples/sec for current
Per channel:
• 1.25 samples/sec for voltage
• 0.75 samples/sec for current
Single channel:
• 1.25 samples/sec for voltage
• 0.75 samples/sec for current
Input Impedance: 900K ohms (min.)
Built-in Resistor for Current Input: 120 ohms
Isolation: 3K VDC or 2K Vrms

Analog Output
Resolution: 12 bits
Output Range: 0 to 10 V, 4 to 20 mA
Drive Voltage: 15 VDC for current output
Accuracy:
±0.1% FSR @ 25°C,
±0.3% FSR @ -10 and 60°C,
±0.5% FSR @ -40 and 75°C
Load Resistor: Less than 250 ohms

Power Requirements
Power Consumption: 198 mA @ 24 VDC

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
Ethernet Remote IO ioLogik E2240
Moxa

Ethernet Remote I/O ioLogik E2240

$272.50

Moxa’s ioLogik E2200 Series Ethernet Remote I/O is a PC-based data acquisition and control device that uses proactive, event-based reporting to control I/O devices and features the Click&Go programming interface.

Unlike traditional PLCs, which are passive and must poll for data, Moxa’s ioLogik E2200 Series will, when paired with our MX-AOPC UA Server, communicate with SCADA systems using active messaging that is pushed to the server only when state changes or configured events occur. Additionally, the ioLogik E2200 features SNMP for communications and control using an NMS (Network Management System), allowing IT professionals to configure the device to push I/O status reports according to configured specifications. This report-by-exception approach, which is new to PC-based monitoring, requires far less bandwidth than traditional polling methods.

Moxa ioLogik E2240 Specifications

Inputs and Outputs
Analog Inputs: 8 channels
Analog Outputs: 2 channels

Analog Input
Type: Differential input
Resolution: 16 bits
I/O Mode: Voltage / Current
Input Range: ±150 mV, ±500 mV, ±5 V, ±10 V, 0 to 20 mA, 4 to 20 mA
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
±0.5% FSR @ -40 and 75°C
Sampling Rate:
All channels:
• 10 samples/sec for voltage
• 6 samples/sec for current
Per channel:
• 1.25 samples/sec for voltage
• 0.75 samples/sec for current
Single channel:
• 1.25 samples/sec for voltage
• 0.75 samples/sec for current
Input Impedance: 900K ohms (min.)
Built-in Resistor for Current Input: 120 ohms
Isolation: 3K VDC or 2K Vrms

Analog Output
Resolution: 12 bits
Output Range: 0 to 10 V, 4 to 20 mA
Drive Voltage: 15 VDC for current output
Accuracy:
±0.1% FSR @ 25°C,
±0.3% FSR @ -10 and 60°C,
±0.5% FSR @ -40 and 75°C
Load Resistor: Less than 250 ohms

Power Requirements
Power Consumption: 198 mA @ 24 VDC

Available Models

  • Demo Stock
View product