Ethernet Remote I/O ioLogik E2214

Smart I/O controller with 6DI and 6 relay outputs, Click&Go; Front-end intelligence

$0.00
9% Tax included Shipping calculated at checkout.

Moxa’s ioLogik E2200 Series Ethernet Remote I/O is a PC-based data acquisition and control device that uses proactive, event-based reporting to control I/O devices and features the Click&Go programming interface. Unlike traditional PLCs, which are passive and must poll for data, Moxa’s ioLogik E2200 Series will, when paired with our MX-AOPC UA Server, communicate with SCADA systems using active messaging that is pushed to the server only when state changes or configured events occur. Additionally, the ioLogik E2200 features SNMP for communications and control using an NMS (Network Management System), allowing IT professionals to configure the device to push I/O status reports according to configured specifications. This report-by-exception approach, which is new to PC-based monitoring, requires far less bandwidth than traditional polling methods.

 

ioLogik E2214 Specifications

Inputs and Outputs
Digital Inputs: 6 channels
Relay Outputs: 6 channels
Isolation: 3K VDC or 2K Vrms

 

Digital Input
Sensor Type: Wet Contact (NPN or PNP) and Dry Contact
I/O Mode: DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact(DI to GND):
• On: 0 to 3 VDC
• Off: 10 to 30 VDC
Common Type: 3 points per COM
Counter Frequency: 900 Hz, power off storage
Digital Filtering Time Interval: Software selectable


Relay Output
Type: Form A (N.O.) power relay
Contact Current Rating:
• Inductive Load: 2 A @ 30 VDC, 250 VAC, 110 VAC
• Resistive Load: 5 A @ 30 VDC, 250 VAC, 110 VAC
Minimum permitted load: 1 A @ 5 VDC
Initial Insulation Resistance: 1000 M ohms (min.) @ 500 VDC
Mechanical endurance: 1,000,000 operations
Electrical endurance: 100,000 operations @ 5 A resistive load
Contact Resistance: 100 m ohms (max.)
Pulse Output: 0.3 Hz at rated load


Power Requirements
Power Consumption: 170 mA @ 24 VDC

Ethernet Remote I/O ioLogik E2214
Moxa

Ethernet Remote I/O ioLogik E2214

$0.00

Moxa’s ioLogik E2200 Series Ethernet Remote I/O is a PC-based data acquisition and control device that uses proactive, event-based reporting to control I/O devices and features the Click&Go programming interface. Unlike traditional PLCs, which are passive and must poll for data, Moxa’s ioLogik E2200 Series will, when paired with our MX-AOPC UA Server, communicate with SCADA systems using active messaging that is pushed to the server only when state changes or configured events occur. Additionally, the ioLogik E2200 features SNMP for communications and control using an NMS (Network Management System), allowing IT professionals to configure the device to push I/O status reports according to configured specifications. This report-by-exception approach, which is new to PC-based monitoring, requires far less bandwidth than traditional polling methods.

 

ioLogik E2214 Specifications

Inputs and Outputs
Digital Inputs: 6 channels
Relay Outputs: 6 channels
Isolation: 3K VDC or 2K Vrms

 

Digital Input
Sensor Type: Wet Contact (NPN or PNP) and Dry Contact
I/O Mode: DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact(DI to GND):
• On: 0 to 3 VDC
• Off: 10 to 30 VDC
Common Type: 3 points per COM
Counter Frequency: 900 Hz, power off storage
Digital Filtering Time Interval: Software selectable


Relay Output
Type: Form A (N.O.) power relay
Contact Current Rating:
• Inductive Load: 2 A @ 30 VDC, 250 VAC, 110 VAC
• Resistive Load: 5 A @ 30 VDC, 250 VAC, 110 VAC
Minimum permitted load: 1 A @ 5 VDC
Initial Insulation Resistance: 1000 M ohms (min.) @ 500 VDC
Mechanical endurance: 1,000,000 operations
Electrical endurance: 100,000 operations @ 5 A resistive load
Contact Resistance: 100 m ohms (max.)
Pulse Output: 0.3 Hz at rated load


Power Requirements
Power Consumption: 170 mA @ 24 VDC

View product